FloorProtection

Correx / Coroplast · temporary floor protection

The floor is already finished. Everything after this is risk.

Triple-layer polypropylene board that takes the damage instead of the stone underneath it. Scroll to lay it.

PP board · 500 GSM0 m² laid

What it is

Three layers, one job

A plain polypropylene skin, a thermoformed cone core, and another plain skin, welded together. The core is what does the work: it takes an impact and spreads it, so the load never reaches the floor as a point.

It is waterproof, so grout slurry and paint sit on top instead of soaking through. It is a single polymer, so it recycles without separating laminates. And because it is rigid rather than woven, it can be lifted at the end of a phase and laid again on the next one.

Top skinWaterproof surfaceCone coreSpreads the impactBottom skinGrips the floor

Takes the damage

Impact, abrasion and dropped tools land on a consumable sheet instead of a finished floor you cannot patch.

Stops the wet trades

Waterproof and chemical resistant. Grout slurry, paint and solvent stay on the surface rather than etching the stone underneath.

Comes back up clean

Lifts without residue on polished and oiled finishes, and stores flat for reuse across later phases.

0 m²covered per hour, two-person crew
0+ GSMheaviest grade, for plant and trolleys
0%virgin polypropylene, single polymer

On site

Four steps, one crew, no specialist tools

A two-person team covers roughly 400 m² an hour. The only tools are a knife and a roll of low-tack tape.

Polished marble floor, swept and bare, before protection board is laidRender
01 · Sweep and dry. Grit trapped under the board is what scratches.
PP bubble guard board part-laid across a marble floor, leading edge mid-runRender
02 · Lay with a 50 mm overlap at every seam.
Close view of the thermoformed cone lattice on laid protection boardRender
03 · Tape seams and edges. Low-tack only on finished surfaces.
Corner of protection board lifted back, revealing undamaged marble underneathRender
04 · Lift clean. The floor underneath is the whole product.

Scale

Sized for a single villa or a whole tower

The same board, specified up or down by GSM. No named case studies yet: this is what the product is engineered to handle, not a claim about a specific past client.

1000 GSM+

Hotel & hospitality fit-out

Typical scaleUp to 12,000+ m² per programme
175–250 GSM

Premium residential handover

Typical scale200–1,000 m² per home
500 GSM

Corporate office relocation

Typical scale1,000–5,000 m² per floor

Grades

Pick by what is walking on it

GSM is the number that matters, not thickness. It tells you how much polypropylene is actually in the sheet, which is what determines whether it survives a loaded trolley or splits under one.

By trade

The damage is different for everyone

A tiler is fighting slurry. A mover is fighting one loaded trolley for one day. A fit-out contractor is fighting a landlord’s handover clause. Same board, different grade and different argument.

Specification

The full sheet

Sheet size1830 × 1220 mm (6 × 4 ft)500 GSM thickness3.5 mmConstructionTriple layer, welded
ConstructionTriple layer: plain top skin, thermoformed cone core, plain bottom skin, welded
Material100% virgin polypropylene (no recycled fill)
Standard sheet1830 × 1220 mm (6 × 4 ft); roll formats to order
Water & chemicalWaterproof; resistant to oils, solvents and grout slurry
ReuseMultiple project cycles when lifted and stored flat
End of lifeRecyclable as PP, a single polymer with no laminate separation needed

Technical specification sheet

Full technical data, including fire ratings, compressive strength, and material tolerances for every grade.

Coverage

What it looks like going down

Part coverage through to a fully sheeted floor. These are renders generated from the product’s own geometry, not photographs of past projects.

Protection board covering roughly two thirds of a stone floorRender
Part coverage: board advancing across an open floor plate.
Stone floor fully covered edge to edge with protection boardRender
Full coverage, edge to edge, seams overlapped.
Laid protection board seen at working distance, cone lattice visibleRender
At working distance, the cone core carrying the load.

Export Quality Correx & Coroplast

Factory-direct export pricing

Skip the middlemen. We supply interior designers, contractors, and builders across the US, UK, EU, and Australia at unbeatable wholesale rates. Lock in your order today.

Stack of Bubble Guard Sheets
MOQ: 25–30 packetsFOB Gujarat — transport extra

PP Bubble Guard Floor Protection Sheet

Size: 6 ft × 4 ft | Colors: White & Grey

$0.43/ unit

Select Variant

Packing/Coverage: 80 Pcs

Stack of Corrugated Sheets
MOQ: 25–30 packetsFOB Gujarat — transport extra

PP Corrugated Sheet (Floor Protection Grade)

Size: 6 ft × 4 ft | Colors: White & Grey

$0.71/ unit

Select Variant

Packing/Coverage: 100 Pcs

EPE Foam Roll
MOQ: 50 rolls (mix allowed)FOB Gujarat — transport extra

EPE Foam Floor Protector Roll

Color: Blue | Lengths vary based on thickness

$0.026/ unit

Select Variant

Packing/Coverage: 602 Sq.Ft.

100% advance payment • GST 18% extra (India domestic) • FOB Gujarat — transport extra • Quote valid for 1 day

Tell us the area, we will tell you the grade

Rough square metres is enough to price it. No account, no signup, and a reply within one working day.

Get a quote
Get a quoteEmail us
Correx & Coroplast | Temporary floor protection boards